Intercom: Audio, Video Intercom Systems  (2,567)

Provides a normally open dry contact closure upon call-in at a tenant station Also provides a contact to turn on external light at entrance station when calling tenant station

Vandal-resistant with 16-gauge stainless steel construction Flexible design can be mounted to either side of the door 1-gang hole pattern allows for easy installation

Flexible design can overhang mullion on either side of the door Wire cutouts allow for installation when there is an external conduit Clearance for Cat-5/6 cables prevents overbending

An 18-Gauge stainless steel enclosure designed for surface mounting the JO-DVF, JP-DVF, and JP-DVF video door stations Weather resistant Vandal-resistant Inside space for cabling Mounts to flat wall surface Opening at bottom for drainage

An 18-Gauge stainless steel surface mount 30° box designed for angle mounting the JO-DV, JP-DV, and JV-DV video door stations Applicable for wide or double door entrances where the door station needs to be mounted off to the side of the door, and provides a better viewing angle for the camera Weather resistant Vandal-resistant Inside space for cabling

An interface between the door release contact on the Aiphone master station or CEU and the actual release mechanism Form C relay for 18-24V DC intercom systems Both normally open and normally closed output options

Vandal resistant stainless steel Mounts Intercom and Access Control device together Any 1-gang Audio-only or Audio Video Door Station can be used Blank faceplate allows wide range of mounting options Hooded covering to protect units from direct exposure to weather Tamper resistant mounting hardware

Reflective EMERGENCY lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

Made of 12 gauge stainless steel Fully enclosed beacon/strobe light on top Emergency Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

UL-514-A listed electrical box included at the base Access panel at the rear base of the tower Built-in threaded studs in base of the tower ASSISTANCE signage Beacon/Strobe is always lit; flashes during emergency call-in (Requires 24V DC) Weather and vandal resistant LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meets ADA regulations

ASSISTANCE lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) Camera arm with universal pipe threading Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

EMERGENCY lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

ASSISTANCE lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) High-power speaker Camera arm with universal pipe threading Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

Aiphone GT-VP is a vandal resistant panel for GT-VB camera module.

Aiphone GF-10KP is a vandal resistant panel for GT-10K keypad module.

Aiphone GT-AD is an address module for displaying a building name or address.

Aiphone GF-BP is a vandal resistant blank panel to cover open module space on GT Series entrance station.

Aiphone GF-4P is a 4-call button panel for GT-SW.

Aiphone GT-203HB is a vandal resistant 2x3-module surface mount box for GT Series entrance panel.

Aiphone SBX-GTDMB is a stainless steel surface mount box.

Provides ability to select/call 16 additional door/sub stations Mounts directly to Master Station or other AX-16SW with supplied brackets

Wiring hub for AX system using Cat-5e Two 24V DC power supply input terminals Rack mountable Controls all functionality of AX system Two BNC composite video outputs and video switching triggers CO line transfer (requires Viking K-1900-5 programmable auto-dialer) Programmable functionality via supplied software

for EL-9S

Aiphone C2-PE-100 is a polyethelyn cable of 100 metres.

4 core 0.9mm diameter solid copper, polyethylene insulation 200m.

Aiphone CVFS-1  is a flush mount 1 button panel with MK-DAC pan and tilt.

Weather resistant Vandal-resistant Inside space for cabling Mounts to flat wall surface Opening at bottom for drainage

Allows desk mounting of master and/or handset station Station is propped up for easier viewing Pre-drilled mounting holes Constructed with sturdy ABS plastic Adjustable to 45° or 60° angles

Mounts JO-DV, JP-DV, or JV-DV to a door frame or mullion Designed to fit unit precisely and conceals wiring inside Can mount to either right or left of door

Steel construction Mounts to a door mullion of a glass entry Weather resistant for outdoor use Mounts door station at 45° angle Mounts any 1-gang surface mount Aiphone Audio-only or Audio Video Door Station

An adaptor for the JO Series video intercom system Allows two video door stations to be used in a standard or app-enabled system The adaptor has inputs for two JO Series video door stations and outputs to control door release for each of those door stations When a visitor calls at the door station, his image will be displayed on the inside station(s) The person at the JO-1MDW, JO-1MD, or JO-1FD, answers the call, and if they decide to grant the visitor entry, pushes the door release button to activate the electric lock only at the associated door If one door station is in use, the call button on the other door station will not activate a call-in

Made of 12 gauge stainless steel Fully enclosed beacon/strobe light on top Assistance Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

Made of 12 gauge stainless steel Caged beacon/strobe light on top Assistance Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

UL-514-A listed electrical box included at the base Access panel at the rear base of the tower EMERGENCY signage Beacon/Strobe is always lit; flashes during emergency call-in (Requires 24V DC) Weather and vandal resistant LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meets ADA regulations

ASSISTANCE lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

ASSISTANCE lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

Emergency call from tenant station to GT-MK(B) Pull Cord Switch suitable for wet locations Normally Closed mechanically latching switch rating of 24 VDC at 500mA May be actuated by pulling on nylon cord or by pulling down the red actuator

Aiphone GT-NSP-L is a vandal resistant panel for GT-NSB display module.

EMERGENCY lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) High-power speaker Camera arm with universal pipe threading Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

Aiphone GF-AP is a vandal resistant panel for GT-AD address module.