Access Control Accessories  (1,264)

The PE80 Series is the next generation of exit devices. Designed with innovation in mind, the powerful and exquisite exit device introduces new and enhanced features. Ideal for environments that require maximum strength and durable security solutions, all configurations (rim, mortise, surface vertical and concealed vertical rod) exceed ANSI/BHMA Grade 1 requirements.

Everswitch SMF5 is a 18 mm switch with IP68 protection. It is ideal for use in rough environments.

A maintenance‑free, sealed lead‑acid, standby and auxiliary power source that provides long service life and dependability Suitable for supplying backup power for fire, security, and access control systems during AC power failures Fully rechargeable Maintenance‑free

WayPoint17A provides 24VAC or 28VAC distributed via one or two output(s) for powering CCTV Cameras, heaters and other video accessories.

The Everswitch SMA1 is a 22.5 mm non-illuminated switch with IP69 protection.

Mounting plate with four DIN rails for 19” racks 4 rack units/ 88 horizontal pitchs Up to four rails for AMC devices

The Everswitch SBR2 22 mm illuminated switch is rugged, extremely durable, and with no moving parts. Switch is immune to ESD and generate no EMI or RFI. A power supply is not needed for switch operation.

Everswitch SML1 is a 22.5mm illuminated switch with 12” AWG 24 wires, in a wide rang of dimensions.

Everswitch SML3 is a 28.5 mm illuminated switch with 12” AWG 24 wires, in a wide rang of dimensions.

Everswitch SBF2 18.6 mm switch is sturdy, long life, with no moving parts, 100% sealed, resistant to EMI and RFI and needs no power supply.

Designed to accommodate ACS6100 controller, door and I/O boards in International installations Supports up to 16 doors Locking cabinet DC power supply included Indoor rated Mounting hardware for controller, door and I/O boards included Battery fault monitoring Does not support door power CE, UL294

WayPoint30A provides 24VAC or 28VAC distributed via one or two output(s) for powering CCTV Cameras, heaters and other video accessories.

Altronix ACM8CB converts one (1) 12 to 24 volt AC or DC input into eight (8) independently controlled Class 2 rated PTC protected power-limited auto-resettable outputs rated at 2.5A each. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. ACM8CB will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed to be powered by one common power source which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

A 12 V sealed lead‑acid battery that acts as a maintenance‑free standby and auxiliary power supply Provides long service life and dependability Suitable for supplying backup power for fire, security, and access control systems during AC power failures

The Everswitch SBR3 27 mm illuminated switch is rugged, extremely durable, and with no moving parts. Switch is immune to ESD and generate no EMI or RFI. A power supply is not needed for switch operation.

Everswitch SBS1 is a 19.5 mm switch with 12” AWG 24 wires or connector. The switch comes with 10 W breaking capacity and 200mA switching current.

Everswitch SBS2 is a 19.5 mm switch with no moving parts,100% sealed, resistant to EMI and RFI and needs no power supply. It is supplied with 12” AWG 24 wires or connector , in a wide range of dimensions.

Everswitch SMF2 is a 16 mm switch. It is ideal for use in rough environments.

Everswitch SMF4 is a 16 mm switch with IP68 protection. It is ideal for use in rough environments.

Everswitch SBA1 is a 22.5 mm continuous and toggle piezo switch with no moving parts, 100% sealed, resistant to EMI and RFI and needs no power supply. It is supplied with 12” AWG 24 wires or connector , in a wide range of dimensions.

WayPoint10A provides 24VAC or 28VAC distributed via one or two output(s) for powering CCTV Cameras, heaters and other video accessories.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

Altronix DL1 is a 1 second to 1 minute door control timer that is used for basic door operation. This timer can be activated with a momentary or maintained trigger. Input12 volt - 24 volt AC or DC operation. RelayDry relay output (1 form "C" contact, rated @ 2A).12VDC regulated beeper output. FeaturesIsolated AC or DC voltage 5V-24V trigger.Time adjustable from 1 second to 1 minute.Momentary or maintained trigger. Visual IndicatorsIndicates relay is energized. TemperatureOperating 0ºC to 49ºC (32ºF to 120ºF).Storage - 20ºC to 70ºC ( - 4ºF to 158ºF).Relative Humidity 85% +/- 5%.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

GB/UHR903 is a radio frequency vehicle access receiver (it can used with the GB/XQT904 transmitter). It connects 2 vehicle receivers per IXP220 (GB/IPS963) system controller or GB/IPS920i door controller with the GB/UHR903 being within 10m of the controller.

BPT IMPRO B-SHO oscar door control unit

BPT GB/ITR901 is an infrared receiver (use with the GB/IVT900 vehicle transmitter that requires installation in the vehicle). Connect 2 vehicle receivers per IXP220 (GB/IPS963) system controller or GB/IPS920i door controller with the GB/ITR900 being within 8m of the controller.

This integration is a high-level interface facilitating control and management of C.Q.R.iT® and C.Q.R.iT® eXtreme key cabinets and locker systems via Gallagher Command Centre. To eliminate manual and duplicate data entry, Cardholders and Access Groups are automatically imported from Gallagher Command Centre into the C.Q.R.iT® key cabinets and lockers. Cardholders inherit access based on their Access Group membership and can instantly use allocated Keys and Assets stored in the key cabinets and lockers. All transaction log data from the keys cabinets and lockers, including alarms, are sent back to Gallagher Command Centre to provide a centralized reporting facility, eliminating the need for staff to monitor separate systems. The interface can also be configured to employ Gallagher Command Centre Anti-Tailgating features to prevent Cardholders from exiting the facility if they have not yet returned their keys or assets to the relevant cabinet or locker.

Allows to connect locking accessories, such as a door opener, a card reader, etc 10 m long Suitable for the EL420 and EL560 locks

Gallagher provides specialized cables ideal for the high speed HBUS communications protocol, and use in the installation of security systems. An outdoor version is also available for use in installations that require additional protection from the environment. Features and benefits: Superior voltage drop performance for the DC supply conductors, equivalent to three times the distance of a CAT5 cable. Stranded conductors to allow easy distribution to multiple devices. Wire sheaths match HBUS colours for easy recognition. 300 meters of HBUS in an easy-feed box. 1 meter markings along the entire cable.

Gallagher provides a high-level integration between Command Centre and the Croene Electronic Key Cabinet. This integration allows Command Centre to manage user access to keys within the cabinet. Access to the cabinet can be provided to specific users at specified times. Users can be identified by PIN, MIFARE®, or DESFire credential. No additional hardware, devices, or software licenses are required. Creone cabinets are available in a range of models and sizes to suit your business.  Key cabinets can be expanded by adding more compartments or key hooks as required and can be spread across multiple geographical locations while being monitored centrally.

DIGI*TRAC spare parts kit.  Includes: MPB1 (memory protection battery - replacable), FKIT (fuse assortment and fuse holder), one HDR (heavy duty relay - door), one MDR (medium duty relay - alarm).

Morse Watchmans Tamper Proof Key Ring 1.5" x 1.5" incorporate ease-of-use, a tamper-proof locking mechanism and unique identification system while offering the flexibility to add or remove keys without destroying the more expensive ring. It has a replaceable hub technology that allows to re-use the tamper proof key ring and replace the hub at a fraction of the cost.

Pivoting mount technology and central wire entry for tensioner and wire alignment. Easier, more intuitive installation. Reduced fence installation time. Continuous conductive path. Retrofittable. Easier maintenance and trouble shooting. Rated for continuous outdoor use. Compatible with previous generation products - fits standard Gallagher security posts.