Access Control Accessories  (1,246)

Everswitch SBA2 is a 22.5 mm continuous and toggle piezo switch with no moving parts, 100% sealed, resistant to EMI and RFI . It is supplied with 12” AWG 24 wires or connector , in a wide range of dimensions.

VdS 2119-compliant DIN-rail click system for easy mounting and replacement Tamper-detection AMC2 enclosure with single DIN rail and mountings for VdS 2119-compliant installation An AMC2 control panel within it may arm/disarm VdS-Class C intrusion detection systems

Mounting plate with two DIN rails for 19” racks 4 rack units/ 88 horizontal pitchs Battery bracket Srew socket for PBC-60 Cable kits to connect the power supply

Mounting plate with four DIN rails for 19” racks 4 rack units/ 88 horizontal pitchs Up to four rails for AMC devices

Produced in accordance with UL guidelines and is used for securely mounting and housing an AMC2 (Access Modular Controller) and a power supply unit 1 DIN rail system for easy mounting and replacement Designed for indoor wall mounting It ensures a secure installation and housing of one AMC2 or one AMC2 extension board, one power supply unit and two batteries The steel housing includes an LED for power indication, a tamper contact and pre-stamped knockouts

AMC2 enclosure with single din rail, power supply unit and pre-assembled cables Produced in accordance with strict guidelines and is used for securely mounting and housing an AMC2 (Access Modular Controller) and a power supply unit

Everswitch SML2 is a 22.5mm illuminated switch with 12” AWG 24 wires, in a wide rang of dimensions.

Everswitch SMF6 is a 16mm non-illuminated piezo switch with IP68 protection. It is ideal for use in rough environments.

Everswitch SBF1 18.6 mm switch is sturdy, long life, with no moving parts, 100% sealed, resistant to EMI and RFI and needs no power supply.

WayPoint17A provides 24VAC or 28VAC distributed via one or two output(s) for powering CCTV Cameras, heaters and other video accessories.

Everswitch SMF5 is a 18 mm switch with IP68 protection. It is ideal for use in rough environments.

A maintenance‑free, sealed lead‑acid, standby and auxiliary power source that provides long service life and dependability Suitable for supplying backup power for fire, security, and access control systems during AC power failures Fully rechargeable Maintenance‑free

The Everswitch SBR2 22 mm illuminated switch is rugged, extremely durable, and with no moving parts. Switch is immune to ESD and generate no EMI or RFI. A power supply is not needed for switch operation.

Everswitch SML3 is a 28.5 mm illuminated switch with 12” AWG 24 wires, in a wide rang of dimensions.

The Everswitch SMA1 is a 22.5 mm non-illuminated switch with IP69 protection.

Everswitch SBA1 is a 22.5 mm continuous and toggle piezo switch with no moving parts, 100% sealed, resistant to EMI and RFI and needs no power supply. It is supplied with 12” AWG 24 wires or connector , in a wide range of dimensions.

Everswitch SBF2 18.6 mm switch is sturdy, long life, with no moving parts, 100% sealed, resistant to EMI and RFI and needs no power supply.

Altronix ACM8CB converts one (1) 12 to 24 volt AC or DC input into eight (8) independently controlled Class 2 rated PTC protected power-limited auto-resettable outputs rated at 2.5A each. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. ACM8CB will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed to be powered by one common power source which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

WayPoint30A provides 24VAC or 28VAC distributed via one or two output(s) for powering CCTV Cameras, heaters and other video accessories.

Everswitch SML1 is a 22.5mm illuminated switch with 12” AWG 24 wires, in a wide rang of dimensions.

A 12 V sealed lead‑acid battery that acts as a maintenance‑free standby and auxiliary power supply Provides long service life and dependability Suitable for supplying backup power for fire, security, and access control systems during AC power failures

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

The Everswitch SBR3 27 mm illuminated switch is rugged, extremely durable, and with no moving parts. Switch is immune to ESD and generate no EMI or RFI. A power supply is not needed for switch operation.

Everswitch SBS1 is a 19.5 mm switch with 12” AWG 24 wires or connector. The switch comes with 10 W breaking capacity and 200mA switching current.

Everswitch SBS2 is a 19.5 mm switch with no moving parts,100% sealed, resistant to EMI and RFI and needs no power supply. It is supplied with 12” AWG 24 wires or connector , in a wide range of dimensions.

Everswitch SMF2 is a 16 mm switch. It is ideal for use in rough environments.

Everswitch SMF4 is a 16 mm switch with IP68 protection. It is ideal for use in rough environments.

WayPoint10A provides 24VAC or 28VAC distributed via one or two output(s) for powering CCTV Cameras, heaters and other video accessories.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

Altronix DL1 is a 1 second to 1 minute door control timer that is used for basic door operation. This timer can be activated with a momentary or maintained trigger. Input12 volt - 24 volt AC or DC operation. RelayDry relay output (1 form "C" contact, rated @ 2A).12VDC regulated beeper output. FeaturesIsolated AC or DC voltage 5V-24V trigger.Time adjustable from 1 second to 1 minute.Momentary or maintained trigger. Visual IndicatorsIndicates relay is energized. TemperatureOperating 0ºC to 49ºC (32ºF to 120ºF).Storage - 20ºC to 70ºC ( - 4ºF to 158ºF).Relative Humidity 85% +/- 5%.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 24VDC fuse protected outputs. These power outputs can be converted to dry form "C" contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

GB/UHR903 is a radio frequency vehicle access receiver (it can used with the GB/XQT904 transmitter). It connects 2 vehicle receivers per IXP220 (GB/IPS963) system controller or GB/IPS920i door controller with the GB/UHR903 being within 10m of the controller.

BPT IMPRO B-SHO oscar door control unit

BPT GB/ITR901 is an infrared receiver (use with the GB/IVT900 vehicle transmitter that requires installation in the vehicle). Connect 2 vehicle receivers per IXP220 (GB/IPS963) system controller or GB/IPS920i door controller with the GB/ITR900 being within 8m of the controller.

Allows to connect locking accessories, such as a door opener, a card reader, etc 10 m long Suitable for the EL420 and EL560 locks