Access Control Accessories  (1,113)

Provides 1 input & 4 output ports, each optically isolated RS232 or RS485, with status LEDs.  Up to 16 DIGI*TRAC controllers per output port.  Cascading supported (2 levels deep).  Includes enclosure, 115 VAC power supply, battery, key lock.

Memory Protection Battery - replacable.  NiCad battery.  Universal replacement for DIGI*TRAC memory protection.  2 leads solder to motherboard - thereafter replacable without soldering using plug connectors.  Includes nylon tie and adhesive.

The Borer Lock Manager/Power Adapter enables a complete door installation including electric release, door sensor and card readers, to be centrally powered over a single 300m (1000 ft) length of CAT5/6 cable. This eliminates the need and costs of providing mains powered fused spurs at every door.Both Power and Data are supplied from the Borer Midspan Bridge using IEEE 802.3af (PoE) based power delivery systems.The Power Adapter/Lock Manager circuit board has a small footprint and is designed to be mounted together with the "Press to Exit" switch in a single gang electrical - wall box.It performs the following functions: Breaks out the power and data supplied down a standard CAT5e cable by a Borer Midspan Bridge Monitors door status settings (door open, lock status and exit request button pressed) Manages the power supplied to operate a solenoid operated door lock or strike. These need an initial high current to engage the solenoid and then a reduced static current to maintain it. The power delivered by most systems is not current restricted which will cause the lock, after it has been switched, to continue to consume power. The extra energy consumed raises the temperature of the solenoid. By managing and limiting the power delivered, less heat is generated. As a result, less energy is used and the lock is not stressed, extending its operational lifespan. Power over CAT5e cable technology is used to power equipment where it is inconvenient, expensive or not possible to provide a separate mains power outlet.This solution requires two components as follows: A Midspan Bridge at the source, which injects power into a standard CAT5e cable system without affecting the data A Lock Manager/Power Adapter at the destination, which splits power and data for delivery to local devices. The power management chipset employed (IEEE 802.3af standard), is designed for Power over Ethernet applications, providing protection against short circuit, polarity reversal and the accidental connection of non-compliant equipment.For door access control applications the Power Adapter/Lock Manager is located on the secure side, either in the "Press to Exit" switch housing or next to electric release.Communications between the Lock Manager and Card Reader is via a four core cable which supplies encoded data and power. This enhances security by removing the opportunity to gain access by dismantling the card access reader head and shorting out the lock or power supply cable ends.Benefits: Enhances Security preventing door access by tampering with the card access reader head or controller Safeguards the Electrical Equipment connected to the circuit by only supplying power following device identification and evaluation Protects the CAT5e Cable by measuring the energy delivered providing a 48 Volts current limited power source Reduces Equipment Cost by eliminating the requirement for local main outlets, power supply and battery at every doorReduces Installation Cost by eliminating the local mains wiring, which in most countries, for legal or insurance reasons, has to be installed by a qualified and/or licensed electricianUp to 80% Reduction in Energy Consumption by managing the power being supplied to operate the electric door release      

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Aritech 1078CW-G is a recessed steel door contact with wire leads. It is designed specifically for use in the steel doors commonly found in commercial building applications. The magnet housing isolates the magnet from the surrounding steel for maximum gap distances, both make and break.

Exit buttons may be used with Compact, Switch2 or Net2 systems.  They are designed to match our range of PROXIMITY readers and keypads.  The exit buttons are supplied with a choice of black or white fascias which can be fi tted in the final stages of installation. 

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Exit buttons may be used with Compact, Switch2 or Net2 systems.  They are designed to match our range of PROXIMITY readers and keypads.  The exit buttons are supplied with a choice of black or white fascias which can be fi tted in the final stages of installation. 

Monitors unauthorised opening and closure of doors or windows Ultra-thin design at only 4mm thickness Discreet mounting in doors and windows Powered by a pre-inserted long lasting battery Minimum power consumption Faster speed of signal transmission, reliability, and enhanced communication range Supervisory signals ensure proper operation Low battery detection Simple and flexible wireless installation Suitable for residential and commercial premises

Request-to-exit button with key icon Flush mount To open the door from the inside, if access is only being monitored from one side

The Interlogix 1078 Series Steel Door contacts are designed specifically for use in the steel doors commonly found in commercial building applications. On available models a terminal connection (T) makes installation easier. Simply strip the wire, insert it into the terminal block and tighten. The terminal accepts any wire size from 14 to 22 gauge, and has a unique one piece design for added strength.

Aritech 2847T-M is a explosion proof conduit fitting magnetic terminal contact with SPDT switches.

Aritech 1078CW-N is a recessed steel door contact with wire leads. It is designed specifically for use in the steel doors commonly found in commercial building applications. The magnet housing isolates the magnet from the surrounding steel for maximum gap distances, both make and break.

Alpro ALP-DR-EN-28A is a surface door closer with standard arm and backcheck. It is suitable for right or left hand installation and is easy to install, use and adjust.

Powered by pre-inserted Lithium battery for easy installation Mounted on door or window frames Tamper protection to prevent unauthorised removal, sabotage or unsteady installation Randomised supervision signals for system integrity checks and troubleshooting Low battery detection Power magnet allows for overall side-to-side gap distance of 32mm LED serving as a fault and test mode indicator Compliant with CE requirements Certified to Standard: EN 50131 Grade2, ClassⅡ

Comes with charger circuit. Available in small metal case. Also comes without charger circuit (models ARD).

The Alpro Hardware Division of IEC Limited has announced the release of the new Alpro PB86 proximity switch. Designed to be used in conjunction with the full range of Alpro electric strikes, electric bolts and general access control products out in the field, this proximity switch offers contactless features offering sterile and hygienic operation. The switch has a proximity distance adjustable from 5-20cms, along with an adjustable relay trigger from 1 to 9 seconds. The switch has easy indication of operation status and can be operated remotely by a small keypad. The switch is suitable for indoor use only. A simple swipe of the hand operates the switch, ensuring no contact is required. A feature especially important with the onset of MRSA and other infectious bacteria currently prevalent in hospitals and other communal areas. Keith Parry Alpro's Divisional Sales Manager commented: "In line with our ongoing product development and taking full cognisance of the macro environment, we have brought this new proximity switch to the market, to fulfil market requirements. It is competitively priced and along with Alpro's proven track record of service and reliability will prove to be a winner. Once again reinforcing Alpro's commitment to excellence, making us first choice for locking products."

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing End loading option Variable strength

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing End loading option DDA compliant 90° hold open facility

Alpro ALP-DR-EN-980 is a surface door closer with standard arm. It is suitable  suitable for right or left hand installation and is easy to install, use and adjust.

ALP-DR-EN-170 is a surface door closer with sliding track and arm. It is suitable for right or left hand installation and is easy to install, use and adjust.

Alpro DDA-NHO-T2-U transom door closer is designed to be concealed within the transom header bar of the door. It provides controlled closing of a single or double action aluminium door or doors.

Alpro DDA-NHO-T3-U transom door closer is designed to be concealed within the transom header bar of the door. It provides controlled closing of a single or double action aluminium door or doors.

Exit Device - Pneumatic "PUSH TO EXIT" Switch w/ Plate Exit Button - Narrow - Size: 1-9/16" - Color: Green

Exit buttons may be used with Compact, Switch2 or Net2 systems.  They are designed to match our range of PROXIMITY readers and keypads.  The exit buttons are supplied with a choice of black or white fascias which can be fi tted in the final stages of installation. 

Parabit 300-30037 is an exit button with wide plate and DPDT push button switch.

Full range of RTE exit buttons as standard, architrave plastic or stainless steel. Flush or surface engraved.

Monitors unauthorized opening and closure of doors and windows Ultra-thin design at only 4.2mm thickness Discreet mounting in doors and windows Powered by a pre-inserted long lasting battery Minimum power consumption Supervisory signals ensure proper operation Low battery detection Simple and flexible wireless installation Suitable for residential and commercial premises Compatible with any Z-Wave mesh networks and devices

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing Side loading option Medium Duty

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing Side loading option Heavy Duty

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing Side loading option Medium Duty 90° hold open facility

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing End loading option Medium Duty 90° hold open facility

Designed to be concealed within the transom header bar of the door Provides controlled closing of a single or double action, aluminium door or doors Features built into the closer include dual closing speeds to allow flexibility in closing Short side loading option Heavy Duty 90° hold open facility

Alpro 510100T1-U transom door closer is designed to be concealed within the transom header bar of the door. It provides controlled closing of a single or double action aluminium door or doors.

Alpro 510100T3-U transom door closer is designed to be concealed within the transom header bar of the door. It provides controlled closing of a single or double action aluminium door or doors.