Access Control Cards, Tags & Fobs  (568)

Single port controller. Requires 2MB RAM. 256 access levels / 127 time zones. Supports up to 32 alarm panels (512 inputs) and 32 relay outputs. 2 card access. Timed and zone anti-passback. Wide range of reader types supported. Direct interface to various LANs.

ICLASS Adhesive Tag with 2 Kbyte data storage 2 application areas, one of which can be customised Tags have an embedded wire antenna and an ICLASS chip The Adhesive Tag is recognised and read when held in front of the reader The reading process is passive with a frequency of 13.56 MHz ICLASS Adhesive Tags are dynamic credentials with application areas that can be individually protected All credentials have a unique chip number and a customer (or facility) code ICLASS adhesive tags with an iClass chip are ideal for installations with high-availability systems and where credentials may be exposed to abnormal conditions Adhesive tags are very easy and convenient to use Reading ranges reach up to 5 cm depending on the readers used

Open Architecture Communication Protocol. Expandable up to 24000 Cardholders. Stores up to 4000 transactions. Supports RS-232, Optically Isolated RS-485 and Dial Up Communication. 64 Elevator Floors. MicroELV controllers can be installed with existing LiNC-NET system. Can also intermix with Ultimate Series, IQ Series and SIM Series controllers.

ACT-31B is a factory block-coded transmitter with the following features: compatible with all Linear MegaCode™ receivers and controllers, suitable for everyday installations, ideal for single-family, multi-tenant, and commercial applications.

PCSC REC 20 is ideal for retrofitting or expanding existing card access systems, enabling long-range wireless Wiegand access control for boom gates, garages and general access. The REC-20 can be used in combination with Wiegand cards, offering the same access control to individuals whom require a long range solution in addition to building card access.The REC-20 secure RF Wiegand receiver extracts Wiegand data from within the RF Rolling Code Carrier Frequency.The platform provides full access monitoring and administration functionsfor card and keyfob holders.

ICLASS ID card with 2 Kbyte data storage 2 application areas, one of which can be customised Cards have an embedded wire antenna and an ICLASS chip The card is recognised and read when held in front of the reader The reading process is passive with a frequency of 13.56 MHz ICLASS cards support multiple application areas that can be individually protected All credentials have a unique chip number and a customer (or facility) code Contactless credentials with an iClass chip are ideal for installations with high-availability systems and where credentials may be exposed to abnormal conditions Reading ranges reach up to 12.5 cm depending on the readers used

Open Architecture Communication Protocol. Expandable up to 24000 Cardholders. Stores up to 4000 transactions. Supports RS-232, Optically Isolated RS-485 and Dial Up Communication. 48 Elevator Floors. MicroELV controllers can be installed with existing LiNC-NET system. Can also intermix with Ultimate Series, IQ Series and SIM Series controllers.

Open Architecture Communication Protocol. Expandable up to 24000 Cardholders. Stores up to 4000 transactions. Supports RS-232, Optically Isolated RS-485 and Dial Up Communication. 32 Elevator Floors. MicroELV controllers can be installed with existing LiNC-NET system. Can also intermix with Ultimate Series, IQ Series and SIM Series controllers.

Onboard ethernet communication TCP/IP. LAN/WAN connectivity. IDE controller. 12.000 event transaction buffer.

As an alternative to the traditional mechanical key, the PAC smart card is an easy and reliable means of gaining access to places of work and other secured access points e.g. car park barriers and turnstiles. Its single card solution incorporates access control with applications such as cashless vending and ticketing systems offering a cost effective and enhanced alternative to the conventional proximity card. The PAC smart card is ‘credit card’ thin, ISO 14443A compliant and requires no batteries.

CEM CRD/229/008 DESFire 13.56MHz read/write contactless smart card can be used for a range of different applications from access control to other applications such as cashless vending and public transportation. Using a standardised Mifare Application Directory (MAD), the card contains a structured file system offering security for multiple applications and to support future growth. Utilising Advanced Encryption Standard (AES) -128-bit encryption, the information is securely stored on the card, ensuring that it cannot be cloned and that only valid cards are granted access.

ICLASS Adhesive Tag with 256 byte data storage 2 application areas, one of which can be customised Tags have an embedded wire antenna and an ICLASS chip The Adhesive Tag is recognised and read when held in front of the reader The reading process is passive with a frequency of 13.56 MHz ICLASS Adhesive Tags are dynamic credentials with application areas that can be individually protected All credentials have a unique chip number and a customer (or facility) code ICLASS adhesive tags with an iClass chip are ideal for installations with high-availability systems and where credentials may be exposed to abnormal conditions Adhesive tags are very easy and convenient to use Reading ranges reach up to 5 cm depending on the readers used

Card, Proximity, PVC, 125 KHz, 8, -30 ~ +65, 10 ~ 90

Tag, Proximity, ABS, 125 KHz, 4, -30 ~ +65, 10 ~ 90

Proximity ISO card – 32 bit read only.

ICLASS Adhesive Tag with 2 Kbyte data storage 16 application areas, 15 of which can be customised Tags have an embedded wire antenna and an ICLASS chip The Adhesive Tag is recognised and read when held in front of the reader The reading process is passive with a frequency of 13.56 MHz ICLASS Adhesive Tags are dynamic credentials with application areas that can be individually protected All credentials have a unique chip number and a customer (or facility) code ICLASS adhesive tags with an iClass chip are ideal for installations with high-availability systems and where credentials may be exposed to abnormal conditions Adhesive tags are very easy and convenient to use Reading ranges reach up to 5 cm depending on the readers used

Card, Proximity, PVC, ISO size Printable, 125 KHz, 5.5, -30 ~ +65, 10 ~ 90

Proximity teardrop tag – 32 bit read only.

Customize your swipe cards with site specific logos and messages. Gallagher provides free black and white printing of images and/or text on both sides of ISO cards - a one offsetup cost applies.  

FingerTIP CMOS Chip and System. Interfaces: parallel and serial. Comes with Flexband package or SMD package.

Proximity ISO card - 256 bit read/write.

Proximity teardrop tag – 2048 bit read/write.

Proximity ISO card – 32 bit read only.

Proximity ISO card – 2048 bit read/write.

The KeyPAC & PAC ISO proximity cards are ‘credit card’ thin, ISO 7813 compliant, requires no batteries and carry a lifetime guarantee against electronic failure.

ICLASS keyfob with 256 byte data storage Fastening Slot ICLASS chip

Proximity teardrop tag - 256 bit read/write.

Proximity ISO card – 2048 bit read/write.

The Stanley proximity tokens are available in seven distinctive colours and are fully interchangeable with the existing PAC® token range and are also compatible with Stanley's PAC, Easikey, Oneprox and GDX Indigo proximity readers. Stanley tokens can be programmed into Stanley’s PAC and GDX residential and commercial access control systems so that the user's movement can be monitored and the building protected. Each Stanley token has a unique ID code and need only be held near a door reader for the code to be read and access granted or denied in less than a second. It is compatible with the following readers; PAC Easikey™, PAC® and PAC Oneprox™ GDX Indigo™.

Offers enhanced encryption between the card and reader For use with a Paxton10 system ISO format, standard credit card sizes Can be printed on using a universal card printer Can be used as ID card Card and user information stored in encrypted, password protected sector

Tag, Proximity, ABS, 125 KHz, 4, -30 ~ +65, 10 ~ 90

Card, Proximity, PVC, ISO size Printable, 125 KHz, 5.5, -10 ~ +65, 10 ~ 90

Card, Proximity, PVC, ISO size Printable, 125 KHz, 5.5, -10 ~ +65, 10 ~ 90

Tag, Proximity, ABS, 125 KHz, 4, -30 ~ +65, 10 ~ 90

Touch-to-enter functionality when used with Paxton10 readers Long lasting battery life with backup RFID token

Card, Proximity, Polycarbonate Plastic UL94VO, ISO size Printable, 153 KHz, 86 x 54 x 0.76, 5.79, -10 ~ +65, IP66

Tag, Proximity, PVC, 125 KHz, 2, -30 ~ +65, 10 ~ 90

PCSC BIOCARD creates a secure RFID/NFC/Contactless Smart Card access or payment solution at the lowest price point available today. It builds upon the function of the BIOFOB with the same internal card activation technology, however with the addition of a new fingerprint swipe sensor that has vastly improved its performance and robustness. It is a biometrics activated device that completely encapsulates and secures the traditional RFID Contactless Smart Chip. It is built for flexibility with the following options and specifications, the battery has a typical operating life of ten years with Micro-USB recharge capability, similar as those used in mobile phones.

The Stanley proximity tokens are available in seven distinctive colours and are fully interchangeable with the existing PAC® token range and are also compatible with Stanley's PAC, Easikey, Oneprox and GDX Indigo proximity readers. Stanley tokens can be programmed into Stanley’s PAC and GDX residential and commercial access control systems so that the user's movement can be monitored and the building protected. Each Stanley token has a unique ID code and need only be held near a door reader for the code to be read and access granted or denied in less than a second. It is compatible with the following readers; PAC Easikey™, PAC® and PAC Oneprox™ GDX Indigo™.

PCSC BIOTAG creates a secure RFID/NFC/ Contactless Smart Card access or payment solution at the lowest price point available today. The BIOCARD builds upon the function of the BIOFOB with the same internal card activation technology, however with the addition of a new fingerprint swipe sensor that has vastly improved its performance and robustness. It is a biometrics activated device that completely encapsulates and secures the traditional RFID Contactless Smart Chip. It is built for flexibility with the following options and specifications, the battery has a typical operating life of ten years with Micro-USB recharge capability, similar as those used in mobile phones.